Adresse : Room 1206, Science Avenue 97, Luogang District
Téléphone : +86-769-88888312
.
1. Features ZS-GF-D906W is one kinds of the one-component alcohol silicone sealant which is room temperature curing. This product is a kind of special sealant for solar modules, which have the properties such as excellent moisture,quake-proof, corona resistance and leakage resistance. It has excellent resistance about cold and hot alternative performance,and the temperature range is -60℃～200℃. And this product is completely operators in the European Union RoHS directive requirements.2. The Typical Use Bonding and sealing solar photovoltaic modules of aluminum frame , junction box ,TPT/TPE film ,steel support on the bacd of solar cells,glass ,solar lamps and so on.3. Instructions •Surface cleaning:cleaning the sticklied and coated surface,remove the rust,dirt and oil. •Brush the glue: Unscrew the hose cap (or cut open), pushed the glue to clean the surface, evenly distributed so that will be glued surfaces together and fixed. •Curing: put the glued or sealed parts in the air and let it be natural cured. It’s one curing process that cured from the surface to the internal, in less than 24 hours (at room temperature and 55% relative humidity) glue curing depth of 2 ~ 4mm, if the sizing location more deeper, in particular, which is not easily accessible to the air, then the fully curing time will be extended, if the temperature is low, the curing time will be extended too, sealant is fully cured at least 7 days if the thick have 6mm .4. Note After Operating, unused glue must be sealed and stored , and tighten the cap immediately,. if the seal has a little crust when use it in the next time, remove it and it will not affect the normal use. During the storage process, the canal orifices may appear a small amount of the curing phenomenon, cleared it and it can use it again, and no affection to the product performance.5. Storage And Transportation •The product must be stored in a cool, dry environment below 25 ℃, can be storaged below 25 ℃ for six months. •Such products are non-dangerous goods, can be transported as common chemicals. Be careful during transport and prevent the leakage. •Should be recognized before being used with or without abnormal if the products exceeding retention period.
Before The Curing Appearance Translucent And Half FlowRelative Density0.95～1.05 (g/cm3)Tack Free Time ≤90 (min)Completely Cure Time3～7(d)After the curing
NOTE After operating, the rest of glue must be sealed to store , and tightened the cap immediately. when using it in the next time, if there is a little crust in sealed place, to remove it and it
Before The Curing AppearanceWhite PasteTack Free Time≤10 (min)Extrudability 5~11 (g/s，25℃)Cure Time 3～7(d)After the curing Relative Density1.40～1.45 (g/cm3)Tensile Stren
1. Features ZS-NJ-D939C is one kind of the one-component dealcoholized silicone sealant at room temperature curing with medium viscosity. This product has the properti
Before The CuringPerformance Indicators ABAppearanceGray FluidWhite FluidViscosity 1500～2500(cps)1500～2500(cps)A:B 1:1Mixed Viscosity 1500～2500(cps)Operable Time30～120(min)
1. Features ZS-NJ-D939C is one kind of the one-component dealcoholized silicone sealant at room temperature curing with medium viscosity. This product has the properti
Before the curingAppearanceWhite pasteRelative density1.60～1.70(g/cm3)Surface drying time≤15(min)After the curingTensile strength≥1.5（MPa） Elongation At Break≥150(%)Shear strength&
INSTRUCTIONS1、Clean surface: cleaning adhesion surface and to remove the rust,dust and greasy dirt, etc.2、After sizing: Unscrew the hose cap (or cutting), squeezing the glue on cleaned surface, so
METHOD OF OPERATIONINSTRUCTIONS1、Clean surface: cleaning adhesion surface and to remove the rust,dust and greasy dirt, etc.2、After sizing: Unscrew the hose cap (or cutting), squeezing the glue on
Aide
Ajouter á l'élu
Les marchandises remises
