 |
|
 |
Описание товара |
 |
|
|
|
|
|
Информация о производителе
|
Общий Водонепроницаемый Жидкий раствор
General Waterproof Slurry
Features and benefits:<br>1) Can be applied onto damp surface<br>2) Strong bond strength to substrate of concrete and render. The active<br>element permeates into capillary pores of the substrate and forms a<br>compact waterproof layer<br>3) After the slurry membrane is dried, tile adhesive can be used directly<br>onto the waterproof layer<br>4) Can be used either on interior or exterior wall and floor<br>5) Water resistance and good durability<br>6) Water vapor permeability<br>7) Ageing resistance, innocuous, harmless and environment-protected<br><br>Application scope:<br>1) Indoor and outdoor structures, concrete, cement render and brick wall for<br>waterproofing<br>2) Irrigation works, machine room, foodstuff storehouse, tunnel, underground<br>parking, wall, floor, swimming pool, kitchen, toilet and drinkable water pool<br><br>Substrate preparation:<br>1) The substrate must be firm, clean, even and free from grease, oil<br>2) The obvious pores, sand holes must be plastered with repair mortar, and<br>sharp edge must be removed<br>3) If the temperature of the substrate is too high, it should be damp with<br>water but no obvious water<br><br>Instructions:<br>1) Mixing proportion: 25kg powder: 9kg additive: 0~1kg water<br>2) Add the additive into the container, then pour the powder agent into<br>the water slowly; mix them until a lump-free mixture is achieved<br>3) Use a brush or rolling brush to apply the slurry onto the substrate<br>and spread evenly<br>4) The second coat is applied after the first layer is dried and spread<br>vertically. The third coat is applied when necessary<br><br>Normal dosage:<br>The thickness of the painted film shall be 1.0~1.2mm about 20~25m²/set.<br><br>Note:<br>The above-mentioned dosage is for the case when the substrate is even.<br><br>Precautions:<br>1) Other covering layers can not be done until the waterproof layer is dry<br>completely<br>2) The application cannot be conducted below 5°C; do not apply it in the<br>extremely wet and bad-ventilated surroundings so as to affect the<br>formation of the waterproof film<br>3) Do not mix the cured slurry with water and reuse it<br>4) Do not use it in the place where there are shocks, moving and big cracks<br><br>Shelf life:<br>Unopened products can be stored for up to 12 months in cool dry environment.<br>Liquid additive can not be stored under temperature lower than 5°C.<br><br>Packing:<br>1) 25kg powder + 9kg additive/set<br>2) 5kg powder + 1.8kg additive/set
|
|
|
Другие товары этого производителя : |
|
|
|
|
Общий Водонепроницаемый Жидкий раствор
Product Name: General Waterproof Slurry
Model Number: NIC-K11
Place of Origin: China
Features and benefits:
1) Can be applied onto damp surface
2) Strong bond strength to substrate of concrete and render. The active
element permeates into capillary pores of the substrate and forms a
compact waterproof layer
3) After the slurry membrane is dried, tile adhesive can be used directly
onto the waterproof layer
4) Can be used either on interior or exterior wall and floor
5) Water resistance and good durability
6) Water vapor permeability
7) Ageing resistance, innocuous, harmless and environment-protected
Application scope:
1) Indoor and outdoor structures, concrete, cement render and brick wall for
waterproofing
2) Irrigation works, machine room, foodstuff storehouse, tunnel, underground
parking, wall, floor, swimming pool, kitchen, toilet and drinkable water pool
Substrate preparation:
1) The substrate must be firm, clean, even and free from grease, oil
2) The obvious pores, sand holes must be plastered with repair mortar, and
sharp edge must be removed
3) If the temperature of the substrate is too high, it should be damp with
water but no obvious water
Instructions:
1) Mixing proportion: 25kg powder: 9kg additive: 0~1kg water
2) Add the additive into the container, then pour the powder agent into
the water slowly; mix them until a lump-free mixture is achieved
3) Use a brush or rolling brush to apply the slurry onto the substrate
and spread evenly
4) The second coat is applied after the first layer is dried and spread
vertically. The third coat is applied when necessary
Normal dosage:
The thickness of the painted film shall be 1.0~1.2mm about 20~25m²/set.
Note:
The above-mentioned dosage is for the case when the substrate is even.
Precautions:
1) Other covering layers can not be done until the waterproof layer is dry
completely
2) The application cannot be conducted below 5°C; do not apply it in the
extremely wet and bad-ventilated surroundings so as to affect the
formation of the waterproof film
3) Do not mix the cured slurry with water and reuse it
4) Do not use it in the place where there are shocks, moving and big cracks
Shelf life:
Unopened products can be stored for up to 12 months in cool dry environment.
Liquid additive can not be stored under temperature lower than 5°C.
Packing:
1) 25kg powder + 9kg additive/set
2) 5kg powder + 1.8kg additive/set
|
| |
|
|
Общий Водонепроницаемый Жидкий раствор
Features and benefits:
1) Can be applied onto damp surface
2) Strong bond strength to substrate of concrete and render. The active
element permeates into capillary pores of the substrate and forms a
compact waterproof layer
3) After the slurry membrane is dried, tile adhesive can be used directly
onto the waterproof layer
4) Can be used either on interior or exterior wall and floor
5) Water resistance and good durability
6) Water vapor permeability
7) Ageing resistance, innocuous, harmless and environment-protected
Application scope:
1) Indoor and outdoor structures, concrete, cement render and brick wall for
waterproofing
2) Irrigation works, machine room, foodstuff storehouse, tunnel, underground
parking, wall, floor, swimming pool, kitchen, toilet and drinkable water pool
Substrate preparation:
1) The substrate must be firm, clean, even and free from grease, oil
2) The obvious pores, sand holes must be plastered with repair mortar, and
sharp edge must be removed
3) If the temperature of the substrate is too high, it should be damp with
water but no obvious water
Instructions:
1) Mixing proportion: 25kg powder: 9kg additive: 0~1kg water
2) Add the additive into the container, then pour the powder agent into
the water slowly; mix them until a lump-free mixture is achieved
3) Use a brush or rolling brush to apply the slurry onto the substrate
and spread evenly
4) The second coat is applied after the first layer is dried and spread
vertically. The third coat is applied when necessary
Normal dosage:
The thickness of the painted film shall be 1.0~1.2mm about 20~25m²/set.
Note:
The above-mentioned dosage is for the case when the substrate is even.
Precautions:
1) Other covering layers can not be done until the waterproof layer is dry
completely
2) The application cannot be conducted below 5°C; do not apply it in the
extremely wet and bad-ventilated surroundings so as to affect the
formation of the waterproof film
3) Do not mix the cured slurry with water and reuse it
4) Do not use it in the place where there are shocks, moving and big cracks
Shelf life:
Unopened products can be stored for up to 12 months in cool dry environment.
Liquid additive can not be stored under temperature lower than 5°C.
Packing:
1) 25kg powder + 9kg additive/set
2) 5kg powder + 1.8kg additive/set
|
| |
|
|
Очень Гибкий Пластырь Плитки
Features and benefits:
1) NIC-C6 is specially formulated to produce an extra high strength for fixing
of marble, ceramic tiles and natural stones, especially on exterior walls
2) Can be used on concrete, cement render, plaster board and fiber cement
boards
3) Suitable for laying tiles onto old tiles, concrete, concrete block-work or
rendered brickwork surfaces
4) Due to high flexibility, the adhesive is durable for thermal expansion and
movement
5) Water resistance is excellent
6) Can be used directly out of the container, no watering tiles and walls
required, convenient, quick
Surface preparation:
1) All surfaces should be structurally sound, dry, clean and free from
movement, oil, grease, wax, curing compounds and other loose
contamination materials
2) Can be used directly onto the old tiles
3) For light weight bathroom accessories application
Instruction:
1) Mixing ratio: 3:1 (approx. 7.5kg of water plus 25kg of NIC-C6. Allow the
mixture to stand for 5-10min. Re-stirred when necessary)
2) Spread NIC-C6 onto the substrate evenly using the correct notched trowel.
Do not spread more than 1m² at a time. Press the stone or marble rightly
onto the substrate
3) For tiles with deep grooves or ridges, the adhesive should be buttered
onto the back of the tiles in addition to trowel onto the substrate
4) NIC-C6 can be used rightly onto the old tiles
Dosage:
1) Use 6 x 6mm notched trowel, approx. 2.8-3.0kg/m²
2) Use 10 x 10mm notched trowel, approx. 4-5kg/m²
3) Notched trowels are chosen according to site and surface
Specifications:
1) Adjust time: >5min
2) Open time: ≥10min
3) Surface drying time: approx. 2hrs
4) Appearance: white or grey powder
5) Shrinkage: ≤0.50%
6) Normal shear strength: ≥1.0MPa
7) Water resistance shear strength: ≥0.7MPa
8) Heat treatment resistance shear strength: ≥0.7MPa
9) Freezing-thawing resistance shear strength: ≥0.7MPa
Precautions:
1) Do not mix the cured adhesive with water and reuse it
2) Before using NIC-C6 on concrete, cement render, plasterboard and fiber
cement boards, ensure that the wall is well fastened and stands well
3) Before using NIC-C6 on previously painted surfaces, ensure that the paint is
firmly adhered onto the substrate and no voids under the painted surface
4) Use the product at the temperature between 5-40°C
5) Remove wet adhesive from the face of the tiles with sponge or a damp cloth
before the adhesive dries
Shelf life:
Unopened bags can be stores for up to 12 months in a cool dry environment.
Packing:
25kg/bag, 5kg/bag
|
|
|
|
|
Мозаичный Пластырь Плитки
Features and benefits:<br>1) This product is a brand-new modified polymer adhesive<br>2) Good thixotropy and easy to apply; pasting titles and filling grouts<br>can be finished at a time, saving time<br>3) Excellent water resistance and anti-ageing<br>4) Innocuous, and friendly to environment<br>5) Good water resistance<br><br>Application scope:<br>It is mainly used for various small-sized leatheroid bricks and mosaics<br><br>Surface preparation:<br>1) The surface should be dry, clean, and free from oil stain and other<br>loose substance<br>2) The surface should have a higher strength, with a basic evenness<br>and verticality<br><br>Application:<br>1) Mix the adhesive power with water at a ratio of 25: (8~9) to be<br>lump-free mixture; then let it stand for 3-5 minutes, restir again. The<br>product is now ready to use<br>2) Use a notched apply to trowel the adhesive onto the substrate, with an<br>area of 1m2 each time, then trowel a thin-layer adhesive on the back<br>of tiles and fill up adhesive to the grout joints. then paste tiles onto<br>the substrate press and make it firm<br><br>Dosage:<br>1) Uses 3 x 3mm notched trowel, approx. 2 ~ 2.5kg/m.m<br>2) The above-mentioned dosages are recommended for the even substrate<br><br>Technical parameters:<br>1) Adjust time (min): >5<br>2) Open time (min): ≥10<br>3) Surface drying time: approx. 2h<br>4) Appearance: white powder<br>5) Shrinkage %: ≤0.50<br>6) Normal shear strength: ≥1.0MPa<br>7) Water resistance shear strength: ≥0.7MPa<br>8) Heat treatment resistance shear strength: ≥0.7MPa<br>9) Freezing-thawing resistance shear strength: ≥0.7MPa<br><br>Precautions:<br>1) Before application, check the state of the substrate<br>2) This product had better be used at 5oC∼40oC<br>3) In summer, if the temperature of the substrate is too high ≥40oC),<br>damp it with water, in case of too fast water shortage of the adhesive /<br>on the substrate and affecting quality<br>4) Do not mix the cured adhesive with water and reuse it<br>5) About 2-3 hours after application, use a piece of wet cloth done and<br>sponge clear the surface of the tiles<br>6) Following applications should be done more than 24 hours after this<br>application<br><br>Standard executed:<br>JC/T547-94 (adhesives for ceramic wall and floor tiles)<br><br>Shelf life:<br>It shall be stored in the cool and dry place, and can be stored for 1 year if not<br>opened.<br><br>Packing:<br>20kg/bag, 5kg/bag
|
| |
|
|
Твердый Гидроизолирующий Жидкий раствор
Features and benefits:
1. Can be applied on damp surface
2. Strong bond strength to substrate of concrete and render. The active element permeates into capillary pores of the substrate and forms a compact waterproof layer
3. After the slurry membrane is dried, tiling can be done using Nicbond tile adhesive
4. Can be used either on interior or exterior wall and floor
5. Long term water resistance and good durability
6. Water vapor permeability
7. Water based, non-toxic, and easy to apply
Uses:
1. Interior and exterior
2. Underground garages, cellars, tunnel, concrete units, factory, warehouse, swimming
pools, drinking water tanks
Surface preparation:
1. The surface must be sound, clean and free from any contaminants such as oil and
grease
2. Obvious pore and crack must be plastered with repair mortar, and sharp edge must
be removed
Applications:
1. Mixing ratio: 25kg powder to 6-7kg of water
2. Pour a suitable amount of water into a clean container and slowly add the powder
into water with constant stirring until the lump-free mixture is achieved
3. Keeping interval mixing to avoid deposition
4. Apply rigid waterproofing slurry with a trowel and spread evenly on the surface
5. The second coat is applied after the first layer is dried. The third coat is applied
when necessary
Dosage: about 2.5 to 3 kilograms powder for each square meter
Precautions:
1. Other coating should not be done until the waterproof layer is entirely dry and
cured
2. Do not use the product with the temperature below 0 degree or in the condition
that is very damp
3. Do not mix the cured slurry with water and reuse it
4. Do not add other materials including cement and stone
Standard executed: this product is in accordance with the JC900-2002 standard of
inorganic waterproof and leakage-preventing materials
Packing
25kg/bag
5kg/bag
Shelf life: unopened bags can be stored for up to 12 months in a cool dry environment
|
| |
|
|
Твердый Гидроизолирующий Жидкий раствор
Product Name: Rigid Waterproofing Slurry
Model Number: NIC-K11
Place of Origin: China
Features and benefits:
1. Can be applied on damp surface
2. Strong bond strength to substrate of concrete and render. The active element permeates into capillary pores of the substrate and forms a compact waterproof layer
3. After the slurry membrane is dried, tiling can be done using Nicbond tile adhesive
4. Can be used either on interior or exterior wall and floor
5. Long term water resistance and good durability
6. Water vapor permeability
7. Water based, non-toxic, and easy to apply
Uses:
1. Interior and exterior
2. Underground garages, cellars, tunnel, concrete units, factory, warehouse, swimming
pools, drinking water tanks
Surface preparation:
1. The surface must be sound, clean and free from any contaminants such as oil and
grease
2. Obvious pore and crack must be plastered with repair mortar, and sharp edge must
be removed
Applications:
1. Mixing ratio: 25kg powder to 6-7kg of water
2. Pour a suitable amount of water into a clean container and slowly add the powder
into water with constant stirring until the lump-free mixture is achieved
3. Keeping interval mixing to avoid deposition
4. Apply rigid waterproofing slurry with a trowel and spread evenly on the surface
5. The second coat is applied after the first layer is dried. The third coat is applied
when necessary
Dosage: about 2.5 to 3 kilograms powder for each square meter
Precautions:
1. Other coating should not be done until the waterproof layer is entirely dry and
cured
2. Do not use the product with the temperature below 0 degree or in the condition
that is very damp
3. Do not mix the cured slurry with water and reuse it
4. Do not add other materials including cement and stone
Standard executed: this product is in accordance with the JC900-2002 standard of
inorganic waterproof and leakage-preventing materials
Packing
25kg/bag
5kg/bag
Shelf life: unopened bags can be stored for up to 12 months in a cool dry environment
|
|
|
|
|
Твердый Гидроизолирующий Жидкий раствор
Features and benefits:
1. Can be applied on damp surface
2. Strong bond strength to substrate of concrete and render. The active element permeates into capillary pores of the substrate and forms a compact waterproof layer
3. After the slurry membrane is dried, tiling can be done using Nicbond tile adhesives
4. Can be used either on interior or exterior wall and floor
5. Long term water resistance and good durability
6. Water vapor permeability
7. Water based, non-toxic, and easy to apply
Uses:
1. Interior and exterior
2. Underground garages, cellars, tunnel, concrete units, factory, warehouse, swimming pools, drinking water tanks
Surface preparation:
1. The surface must be sound, clean and free from any contaminants such as oil and grease
2. Obvious pore and crack must be plastered with repair mortar, and sharp edge must be removed
Applications:
1. Mixing ratio: 25kg powder to 6-7kg of water
2. Pour a suitable amount of water into a clean container and slowly add the powder into water with constant stirring until the lump-free mixture is achieved
3. Keeping interval mixing to avoid deposition
4. Apply rigid waterproofing slurry with a trowel and spread evenly on the surface
5. The second coat is applied after the first layer is dried. The third coat is applied when necessary.
Dosage: about 2.5 to 3 kilograms powder for each square meter
Precautions:
1. Other coating should not be done until the waterproof layer is entirely dry and cured
2. Do not use the product with the temperature below 0 degree or in the condition that is very damp
3. Do not mix the cured slurry with water and reuse it
4. Do not add other materials including cement and stone
Standard executed: this product is in accordance with the JC900-2002 Standard of [Inorganic waterproof and leakage-preventing materials
Packing
25kg/bag
5kg/bag
Shelf life: unopened bags can be stored for up to 12 months in a cool dry environment
|
| |
|
|
Пластырь Правления Тепловой изоляции
This product is a kind of high-strength inorganic adhesive specially developed in
allusion to the case that common cement cannot be used as the light construction
material, polystyrene board. It can substitute various organic cementing agent,
lowering greatly the cost of construction.
Features and benefits:
1) Firm adhesion, excellent weather, so as to ensure the permanent firmness and
adhesion of light construction materials
2) Thin mortar technology adopted, with 1.5~3mm thick mortar, so as to lower the
weight of building and the cold and heat bridge in the insulation layers
3) With proper flexibility, able to compensate the temperature difference stress
between the light construction materials and outer decoration paints due to
difference from expansion coefficients
4) Safe, innocuous, anti-mildew and flameproof
5) A certain water resistance
Application scope:
1) The sticking between the polystyrene foam boards of outer insulated
system of the external wall and the basic surface wall, and render of the
protection layer of the foam board
2) The sticking between such light boards as outer wall foam board
decoration line, expanded perlite and so on with the basic surface
3) The bricking mortar for air-added concrete brick, ash sand brick,
powdered coal ash light brick, and gypsum bricklaying
4) Sticking or bricking materials for foam board indoor partition, indoor and
outdoor insulated board
Substrate preparation:
The substrate should be firm, even and free from grease or other loose substance.
Instruction:
1) Mix powder and water at ratio of 3.57:1 (i.e. 20kg powdered: 5.6kg
water), then mix with an electrical mixer until it is equal, lump-free mixture
is achieved; let it stand for 3 minutes, then re-stir and ready to use
2) When it is used for the sticking between the polystyrene foam board, foam
decoration line and the substrate notched trowel, use to spread the
adhesive onto the substrate or the back of the foam, the foam decoration
line, also point pasting method can be used; following application should
be done more than 24 hours after this application
3) When laying light bricks, the moving and adjustment shall be finished
within 10 minutes
Specifications:
1) Tensile and bonding strength (with 20kg/m³ cement board):
a) Normal strength: ≥0.7MPa
b) Water resistance: ≥0.5MPa
2) Tensile and bonding strength (with 20kg/m³ cement board):
a) Normal strength: ≥0.1MPa
b) Water resistance: ≥0.1MPa
3) Operability time: 2.0±0.5h
Dosage:
For the evenness of the basic surface, use notched trowel method or pasting point
method, approx. 3 ~ 4kgsm
Precautions:
1) The product had better be used at 5°C ~40°C
2) Before application, please confirm the verticality and evenness of the
substrate
3) If the surface of the adhesive cement is dry, please remove the surface
crusting
4) Do not add water to the cured adhesive and use it again
Shelf life:
It can be put in the cool and dry place and can be saved for one year if not opened.
Packing:
25kg/bag
|
| |
|
|
Пластырь Правления Тепловой изоляции
Product Name: Thermal-Insulation Board Adhesive
Place of Origin: China
This product is a kind of high-strength inorganic adhesive specially
developed in allusion to the case that common cement cannot be used
as the light construction material, polystyrene board. It can substitute
various organic cementing agents, lowering greatly the cost of construction.
Features and benefits:
1) Firm adhesion, excellent weather, so as to ensure the permanent
firmness and adhesion of light construction materials
2) Thin mortar technology adopted, with 1.5 - 3mm thick mortar, so
as to lower the weight of building and the cold and heat bridge
in the insulation layers
3) With proper flexibility, able to compensate the temperature difference
stress between the light construction materials and outer decoration
paints due to difference from expansion coefficients
4) Safe, innocuous, anti-mildew and flameproof
5) A certain water resistance
Application scope:
1) The sticking between the polystyrene foam boards of outer insulated
system of the external wall and the basic surface wall, and
render of the protection layer of the foam board
2) The sticking between such light boards as outer wall foam board
decoration line, expanded perlite and so on with the basic surface
3) The bricking mortar for air-added concrete brick, ash sand brick,
powdered coal ash light brick, and gypsum bricklaying
4) Sticking or bricking materials for foam board indoor partition,
indoor and outdoor insulated board
Substrate preparation:
The substrate should be firm, even and free from grease or other loose
substance.
Instruction:
1) Mix powder and water at ratio of 3.57:1 (i.e. 20kg powdered: 5.6kg
water), then mix with an electrical mixer until it is equal, lump-free
mixture is achieved; let it stand for 3 minutes, then re-stir and ready to
use
2) When it is used for the sticking between the polystyrene foam board,
foam decoration line and the substrate notched trowel, use to spread
the adhesive onto the substrate or the back of the foam, the
foam decoration line, also point pasting method can be used;
following application should be done more than 24 hours
after this application
3) When laying light bricks, the moving and adjustment shall be finished
within 10 minutes
Specifications:
1) Tensile and bonding strength (with 20kg/m³ cement board):
a) Normal strength: ≥0.7MPa
b) Water resistance: ≥0.5MPa
2) Tensile and bonding strength (with 20kg/m³ cement board):
a) Normal strength: ≥0.1MPa
b) Water resistance: ≥0.1MPa
3) Operability time: 2.0±0.5h
Dosage:
For the evenness of the basic surface, use notched trowel method or
pasting point method, approx. 3 ~ 4kgsm
Precautions:
1) The product had better be used at 5°C - 40°C
2) Before application, please confirm the vertically and evenness of the
substrate
3) If the surface of the adhesive cement is dry, please remove the surface
crusting
4) Do not add water to the cured adhesive and use it again
Shelf life:
It can be put in the cool and dry place and can be saved for one year if
not opened.
Packing:
25kg/bag
|
|
|
|
 |
Аутентификация |
 |
|
|
|
|
|
|
|
|
Моя история |
|
|
|
 Продукты
Категории
Компании
|
 |
|
 |
Специальные ресурсы |
 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
помощь
Добавить в избранное
Отложенные товары
