Russian German French    |    help
   Add to favorite    Favorite products
   
Description
Chemical Materials & Products /  Adhesive Materials / 
Send Request

about this service

Producer information
Company:
Guangzhou Usilicone chemical material Co.,Ltd
 
Address:
Room 1206, Science Avenue 97, Luogang District
 
Phone:
+86-769-88888312

silicone sealant with insulation


Before The Curing AppearanceWhite PasteTack Free Time≤10 (min)Extrudability 5~11 (g/s,25℃)Cure Time 3~7(d)After the curing Relative Density1.40~1.45 (g/cm3)Tensile Strength≥2.5 (MPa)Break Elongation≥500 (%) Shear Strength≥2.0 (MPa)Hardness 45~55 (Shore A)The Temperature Range-60~200 (℃)Volume Resistivity2.6×1015 (Ω·CM)Dielectric Strength20 (kV/·mm)Dielectric Constant3.12Flame Retardant Grade UL94 HBSample: 300mL / tube, 25tubes / box. INSTRUCTIONS1、Clean surface: cleaning adhesion surface and to remove the rust,dust and greasy dirt, etc.2、After sizing: Unscrew the hose cap (or cutting), squeezing the glue on cleaned surface, so that can be distributed uniformly.3、Curing: the part of bonded or sealed were cured naturally in the air. The curing is a process from the surface to the internal, the depth of curing is 2 ~ 4mm within 24 hours (at room temperature and 55% relative humidity), if the location of sizing is too deep, especially when it is not easy to contact the air, then the completely curing time will be extended, if the temperature is low, the curing time will be extended either, the fully curing time need at least 7 days if the thickness of sealant is 6mm. 

Add to BasketAdd to Basket Web addressWeb address



Other goods of this manufacturer :
silicone sealant with non-corrosion for many metal
silicone sealant with non-corrosion for many metal (silicone sealant with non-corrosion for many metal)
1. Features         ZS-GF-D906W is one kinds of the one-component alcohol silicone sealant which is room temperature curing. This product is a kind of special sealant for sola
silicone sealant with non-corrosion for PC
silicone sealant with non-corrosion for PC (silicone sealant with non-corrosion for PC)
Before The Curing  Appearance Translucent And Half FlowRelative Density0.95~1.05 (g/cm3)Tack Free Time  ≤90 (min)Completely Cure Time3~7(d)After the curing   
silicone sealant with special appearance
silicone sealant with special appearance (silicone sealant with special appearance)
NOTE After operating, the rest of glue must be sealed to store , and tightened the cap immediately. when using it in the next time, if there is a little crust in sealed place, to remove it and it
silicone sealant with special appearance
silicone sealant with special appearance (silicone sealant with special appearance)
Before The Curing AppearanceWhite PasteTack Free Time≤10 (min)Extrudability 5~11 (g/s,25℃)Cure Time 3~7(d)After the curing Relative Density1.40~1.45 (g/cm3)Tensile Stren
waterproof silicone sealant
waterproof silicone sealant (waterproof silicone sealant)
1. Features         ZS-NJ-D939C is one kind of the one-component dealcoholized silicone sealant at room temperature curing with medium viscosity. This product has the properti
functional silicone potting sealant
functional silicone potting sealant (functional silicone potting sealant)
Before The CuringPerformance Indicators ABAppearanceGray FluidWhite FluidViscosity 1500~2500(cps)1500~2500(cps)A:B 1:1Mixed Viscosity 1500~2500(cps)Operable Time30~120(min)
damp-proof silicone sealant
damp-proof silicone sealant (damp-proof silicone sealant)
1. Features         ZS-NJ-D939C is one kind of the one-component dealcoholized silicone sealant at room temperature curing with medium viscosity. This product has the properti
good adhesive performance silicone sealant
good adhesive performance silicone sealant (good adhesive performance silicone sealant)
Before the curingAppearanceWhite pasteRelative density1.60~1.70(g/cm3)Surface drying time≤15(min)After the curingTensile strength≥1.5(MPa) Elongation At Break≥150(%)Shear strength&
good adhesive silicone sealant for LED
good adhesive silicone sealant for LED (good adhesive silicone sealant for LED)
INSTRUCTIONS1、Clean surface: cleaning adhesion surface and to remove the rust,dust and greasy dirt, etc.2、After sizing: Unscrew the hose cap (or cutting), squeezing the glue on cleaned surface, so

Likewise in category "Adhesive Materials":
Epoxy Putty Adhesive
Epoxy Putt...
Flexible Joint Filler
Flexible J...
A-B glue, epoxy, resin, acrylic glue, anaerobic adhesive
A-B glue, ...
injection cartridge ( chemical mortar ) Vinylester Styrenefree
injection ...
injection cartridge ( chemical mortar ) Epoxy Acrylate Resin
injection ...
UL 94V0 Hot Melt Adhesive (Electronic Industry)
UL 94V0 Ho...
 
Copyright © 2006 - 2011 Asia.ru
 
eHouseHolding.com