Russian German French    |    help
   Add to favorite    Favorite products
   
Description
Household Goods / 
Send Request

about this service

Producer information
Company:
A RE-POWER TECH INC.
 
Address:
 
Phone:
+886-2-23112121

Photoelectric Pressure Power Implement,pressure power,auto parts


1.Before installing this product,please unscrew the negative charge connector on the battery and take down the breaker, then move under the battery and fix to avoid contacting the battery during operation and cause danger. 2.Unscrew the nut of the positive charge connector on the battery, put the cable end of the photoelectric super conducting intothe screw,and tighten up the nut. 3.Then proceed with the same steps to lock the other end of the photoelectric super conducting onto the major power socket of the generator. Cautions: Afther photoelectric super conductor is installed. Please be sure to tie the cables with a plastic band to fix at a safe place. Do not fix (or contact with) at high heat objects,such as;metal tube,hot water pipe,and engine,or the high temperature will cause resistance to cable and melt it,which in turn will casuse short circuit and fire accident. Please bear this in mind. 4.Find a setscrew close to car body metal plated of the battery,tighten up the third cable (scratch off the metal plated paint a little)to get better current conducting result. Usually,all the cars are installed one or two original negative cables from generator to car body metal. 4-1 If you can not find a setscrew, drill a hole beside to the original negative cable 10~20cm and tighten up. 4-2 If you can not find a setscrew,drill a hole beside to the original negative cable 10-20cm and fasten with a screw. 4-3 If there is difficult for step 4-1 or 4-2,you can find out any set screw of car body metal. 5 For single tanks direct transforming cable, due to it is composed of only two thin 2m cables. Thus the aluminum alloy pipe is not allowed. Please use blue raw material sleeve set to cover on the cable to wrap up. Use a plastic band to tie it up tightly. In order to cover all of the cable, please tie three bonding bands on top of the raw material.

Add to BasketAdd to Basket Web addressWeb address



Other goods of this manufacturer :
strong Oxygen catalyst of the Air,CATALYST,auto parts
strong Oxygen catalyst of the Air,CATALYST,auto parts (strong Oxygen catalyst of the Air,CATALYST,auto parts)
1.Take out the air filter. Open up the small steel clip with hands to peer through 1 cm away from the edge line of the strong oxygen catalyzer(as illustrated).Two at each side. Then use the pointed e
strong Oxygen catalyst of the Air,CATALYST,auto parts
strong Oxygen catalyst of the Air,CATALYST,auto parts (strong Oxygen catalyst of the Air,CATALYST,auto parts)
1.Take out the air filter. Open up the small steel clip with hands to peer through 1 cm away from the edge line of the strong oxygen catalyzer(as illustrated).Two at each side. Then use the pointed e
The battery Strengthener,Current Reinforce Device,auto parts
The battery Strengthener,Current Reinforce Device,auto parts (The battery Strengthener,Current Reinforce Device,auto parts)
1.Use a piece of clean cloth or tissue paper to wipe the front lateral side of the battery. If there is grease on the surface,use a cleaning naphtha or solvent to get rid of the dirt. 2.Tear off the
The battery Strengthener,Current Reinforce Device,auto parts
The battery Strengthener,Current Reinforce Device,auto parts (The battery Strengthener,Current Reinforce Device,auto parts)
1.Use a piece of clean cloth or tissue paper to wipe the front lateral side of the battery. If there is grease on the surface,use a cleaning naphtha or solvent to get rid of the dirt. 2.Tear off the
The battery Strengthener,Current Reinforce Device,auto parts
The battery Strengthener,Current Reinforce Device,auto parts (The battery Strengthener,Current Reinforce Device,auto parts)
1.Use a piece of clean cloth or tissue paper to wipe the front lateral side of the battery. If there is grease on the surface,use a cleaning naphtha or solvent to get rid of the dirt. 2.Tear off the
Dimension Fuel Catalyst,auto parts
Dimension Fuel Catalyst,auto parts (Dimension Fuel Catalyst,auto parts)
The installation Instruction for whole set of Photoelectric Booster Secondary element oil carburetor 1.Please find out the gasoline filter(cup) to get into the in-feed pipe of the engine.(Oil inlet p
Dimension Fuel Catalyst,auto parts
Dimension Fuel Catalyst,auto parts (Dimension Fuel Catalyst,auto parts)
The installation Instruction for whole set of Photoelectric Booster Secondary element oil carburetor 1.Please find out the gasoline filter(cup) to get into the in-feed pipe of the engine.(Oil inlet p
Photoelectric Pressure Power Implement,pressure power
Photoelectric Pressure Power Implement,pressure power (Photoelectric Pressure Power Implement,pressure power)
1.Before installing this product,please unscrew the negative charge connector on the battery and take down the breaker, then move under the battery and fix to avoid contacting the battery during oper
Photoelectric Pressure Power Implement,pressure power
Photoelectric Pressure Power Implement,pressure power (Photoelectric Pressure Power Implement,pressure power)
1.Before installing this product,please unscrew the negative charge connector on the battery and take down the breaker, then move under the battery and fix to avoid contacting the battery during oper

Likewise in category "Household Goods":
Yogurt & Natto Maker
Yogurt & N...
Appliance, Cleaner, Steam Cleaner
Appliance,...
Lithum Polymer
Lithum Pol...
CB SPEAKER
CB SPEAKER
Sine Wave Contact Lens Washer
Sine Wave ...
Patented Apple peeler, Fruit peeler, Vegetable peeler
Patented A...
 
Copyright © 2006 - 2011 Asia.ru
 
eHouseHolding.com