Russian German French    |    help
   Add to favorite    Favorite products
   
Description
Chemical Materials & Products /  Adhesive Materials / 
Send Request

about this service

Producer information
Company:
Guangzhou Usilicone chemical material Co.,Ltd
 
Address:
Room 1206, Science Avenue 97, Luogang District
 
Phone:
+86-769-88888312

waterproof silicone sealant


1. Features         ZS-NJ-D939C is one kind of the one-component dealcoholized silicone sealant at room temperature curing with medium viscosity. This product has the properties of high strength, good adhesion for various metal such as alumina, copper, stainess steel, etc. With excellent dielectric properties and heat resistance. In general, the range of temperature is -60℃~200℃. During the curing process, it will release the alcohols, which no corrosion to the materials such as polycarbonate(PC) and copper. Completely complied with RoHS of EU directive.2. The Typical Application         •Bonding and waterproof sealing guardrail?tube of photo-voltaic industry or LED bulb.          •Bonding and sealing engineering plastics, metal, glass and ceramics, etc.          •The technical parameters before the curing and after the curing process3. Instructions         •Clean surface: clean surface of adherend and coated to remove the rust,dust and greasy dirt, etc.         •After sizing: Unscrew the hose cap (or cutting), squeezing the glue on cleaned surface, so that can be distributed uniformly.         •Curing: the part of bonding or sealing were cured naturally in the air. The curing is a process from the surface to the internal, the depth of curing is 2 ~ 4mm within 24 hours (at room temperature and 55% relative humidity), if the location of sizing is too deep, especially when it is not easy to contact the air, then the completely curing time will be extended, if the temperature is low, the curing time will be extended either, the fully curing time need at least 7 days if the thickness of sealant is 6mm .4.Caution         After operating, the rest of glue must be sealed to store , and tightened the cap immediately. when using it in the next time, if there is a little crust in sealed place, to remove it and it will not affect the normal application. the process of storage , the canal orifices may appear the phenomenon of the curing, to clean it then it can be used again, and the performance of product is not affected.         5. Storage and transportation         •6 months shelf life if stored below 25 ℃ in cool, dry place, when the product passed its expiration date, it should be confirmed without abnormal phenomenon, then that can be used.         •These products don't belong to dangerous goods, so they can be transported as normal chemicals. But be careful of leakage.

Add to BasketAdd to Basket Web addressWeb address



Other goods of this manufacturer :
functional silicone potting sealant
functional silicone potting sealant (functional silicone potting sealant)
Before The CuringPerformance Indicators ABAppearanceGray FluidWhite FluidViscosity 1500~2500(cps)1500~2500(cps)A:B 1:1Mixed Viscosity 1500~2500(cps)Operable Time30~120(min)
damp-proof silicone sealant
damp-proof silicone sealant (damp-proof silicone sealant)
1. Features         ZS-NJ-D939C is one kind of the one-component dealcoholized silicone sealant at room temperature curing with medium viscosity. This product has the properti
good adhesive performance silicone sealant
good adhesive performance silicone sealant (good adhesive performance silicone sealant)
Before the curingAppearanceWhite pasteRelative density1.60~1.70(g/cm3)Surface drying time≤15(min)After the curingTensile strength≥1.5(MPa) Elongation At Break≥150(%)Shear strength&
good adhesive silicone sealant for LED
good adhesive silicone sealant for LED (good adhesive silicone sealant for LED)
INSTRUCTIONS1、Clean surface: cleaning adhesion surface and to remove the rust,dust and greasy dirt, etc.2、After sizing: Unscrew the hose cap (or cutting), squeezing the glue on cleaned surface, so
good adhesive silicone sealant for LED
good adhesive silicone sealant for LED (good adhesive silicone sealant for LED)
METHOD OF OPERATIONINSTRUCTIONS1、Clean surface: cleaning adhesion surface and to remove the rust,dust and greasy dirt, etc.2、After sizing: Unscrew the hose cap (or cutting), squeezing the glue on
good adhesive silicone sealant for LED
good adhesive silicone sealant for LED (good adhesive silicone sealant for LED)
Before The Curing  Appearance Semi Transparent And Semi FlowSpecific Gravity0.95~1.05 (g/cm3)Surface Drying Time ≤15 (min)Curing Time   3~7 daysAfter The CuringTensi
good adhesive silicone sealant for LED
good adhesive silicone sealant for LED (good adhesive silicone sealant for LED)
Before The Curing  Appearance Semi Transparent And Semi FlowSpecific Gravity0.95~1.05 (g/cm3)Surface Drying Time ≤15 (min)Curing Time   3~7 daysAfter The CuringTensi
good heat resistance of power supply potting sealant
good heat resistance of power supply potting sealant (good heat resistance of power supply potting sealant)
Before The CuringPerformance Indicators ABAppearanceGray FluidWhite FluidViscosity 1500~2500(cps)1500~2500(cps)A:B 1:1Mixed Viscosity 1500~2500(cps)Operable Time30~120(min)
inverters silicone potting sealant with waterproof
inverters silicone potting sealant with waterproof (inverters silicone potting sealant with waterproof)
Before The CuringPerformance Indicators ABAppearanceGray FluidWhite FluidViscosity 1500~2500(cps)1500~2500(cps)A:B 1:1Mixed Viscosity 1500~2500(cps)Operable Time30~120(min)

Likewise in category "Adhesive Materials":
Epoxy Putty Adhesive
Epoxy Putt...
Hotmelt Adhesive Film
Hotmelt Ad...
Injection cartridge ( chemical mortar )Epoxy resin
Injection ...
Low Pressure Epoxy Crack Injection System
Low Pressu...
Hot Melt Adhesive
Hot Melt A...
Tensioner Guide
Tensioner ...
 
Copyright © 2006 - 2011 Asia.ru
 
eHouseHolding.com