Informationen über den produzenten
|
.
Detailed Product Description1.304Stainless steel cover 2.Operated Casing: Bright finish 3.Voltage: 220or240 V 4. Frequency: 50or60 Hz Power 2300w 304 stainless steel hand dryer,automatic hand dryer,sensor hand dryer,jet hand dryer,energy saving han dryer | Description | Materials | Technical Specifications | Operation | Specification |General Description• Warm air hand dryer.• Sensor operated by hand approximation.• Airflow temperature electronic regulation.• Maximum power and airflow.• Maximum robustness and vandal-proof.• Suitable for very high traffic facilities.• Recessed kit that conforms to ADAAG projection also available.• It normally goes along with a soap dispenser.* Components and Materials• 304 Stainless steel one-piece high quality and high impact cover bright finish, 1 mm thick. Cover fixed to the base by means of 2 vandal-proof lock screws and lock with special wrench.• Fire resistant plastic alum base and fan scroll, with 4 Ø 8 mm holes for wall mounting. It includes silent-blocks to damp mechanical vibrations.• Universal brush motor, 4,800 rpm, F class, includes a self-resetable thermal cut-off at 120 ºC.• Aluminium centrifugal double asymmetrical inlet fan wheel.• Fe, Al & Cr taped wire heating element mounted on a mica frame that incorporates a self-resetable thermal cut-off at 110 ºC. Automatic disconnection ½ second before motor stop. Automatic regulation of air temperature on ambient temperature.• Fully adjustable (5-20 cm) IR electronic detection sensor by means of a potentiometer. Sensor with polycarbonate viewing window. Selective detection of fixed targets and automatic disconnection system after 15-180seconds(adjustable) of continuous use.* Technical SpecificationsFrequency50/60 Hz Dimensions267×237×150 mm Air velocity101 Km/h Noise level (at 2 m)65 dB Protection levelIPX1 * OperationPlace the hands under the air outflow valve(5-15CM). The dryer will start automatically, and go on with no interruption as long as the hands are kept in the detection range of the sensor. The appliance will stop 3 seconds after the hands are removed from the airflow. As a safety measure, the appliance will stop after 60 seconds.304 Stainless steel one-piece high quality and high impact cover bright finish, 1 mm thick. Cover fixed to the base by means of 2 vandal-proof lock screws and lock with special wrench.• Fire resistant plastic alum base and fan scroll, with 4 Ø 8 mm holes for wall mounting. It includes silent-blocks to damp mechanical vibrations.• Universal brush motor, 4,800 rpm, F class, includes a self-resetable thermal cut-off at 120 ºC.• Aluminium centrifugal double asymmetrical inlet fan wheel.• Fe, Al & Cr taped wire heating element mounted on a mica frame that incorporates a self-resetable thermal cut-off at 110 ºC. Automatic disconnection ½ second before motor stop. Automatic regulation of air temperature on ambient temperature.• Fully adjustable (5-20 cm) IR electronic detection sensor by means of a potentiometer. Sensor with polycarbonate viewing window. Selective detection of fixed targets and automatic disconnection system after 15-180seconds(adjustable) of continuous use.Place the hands under the air outflow valve(5-15CM). The dryer will start automatically, and go on with no interruption as long as the hands are kept in the detection range of the sensor. The appliance will stop 3 seconds after the hands are removed from the airflow. As a safety measure, the appliance will stop after 60 seconds.Surface mounted vandal resistant hand dryer shall be manufactured with one-piece high quality and high impact 1 mm thick304 stainless steel cover and fixed to the base by means of 2 vandal-proof lock screws and lock with special wrench. The back base shall be alum and with 4 holes Ø 8 mm for wall mounting, including silent-blocks to damp mechanical vibrations The dryer shall be activated through an infrared electronic sensor and shall automatically turn off three second after hands are removed. Sensor shall automatically shut dryer off approximately 30 seconds after dryer turn on if inanimate object is placed. The sensor should be fully adjustable (5-20 cm) by means of potentiometer, and should be equipped with a polycarbonate viewing window. Universal motor shall be 150 W, 4.800 rpm, class F, including a self-resetable thermal cut-off which will disconnect at 120ºC. The Fe, Al & Cr heating element should incorporate a self-resetable thermal cut-off which will disconnect at 110ºC. The heating element should be Automatic disconnected ½ second before motor stop. The heating element should incorporate an automatic regulation of air temperature on ambient temperature system. The hand dryer should have an aluminium asymmetrical double inlet fan wheel, and the fan scroll shall be made of a fire resistant plastic 94-V0. Dryer shall deliver 450 m3/h of air at 49 ºC and 95 Km/h velocity during user controlled drying cycle. The dryer shall have a total power of 2.350 Watts with a consumption of 10.9 A. Noise level should be 65 dB at 2 m distances. Protection level against water splashes should be rating Ipx1. Overall dimensions shall be 267×237×150 mm. Unit shall VDE approved and CE marked and comply with electrical safety directives 73/23/CEE& 93/68/CEE and electro-magnetic compatibility directives 89/336/CEE & 92/31/CEE. In recessed version should comply with ADA projection requirements.* SpecificationSurface mounted vandal resistant hand dryer shall be manufactured with one-piece high quality and high impact 1 mm thick304 stainless steel cover and fixed to the base by means of 2 vandal-proof lock screws and lock with special wrench. The back base shall be alum and with 4 holes Ø 8 mm for wall mounting, including silent-blocks to damp mechanical vibrations The dryer shall be activated through an infrared electronic sensor and shall automatically turn off three second after hands are removed. Sensor shall automatically shut dryer off approximately 30 seconds after dryer turn on if inanimate object is placed. The sensor should be fully adjustable (5-20 cm) by means of potentiometer, and should be equipped with a polycarbonate viewing window. Universal motor shall be 150 W, 4.800 rpm, class F, including a self-resetable thermal cut-off which will disconnect at 120ºC. The Fe, Al & Cr heating element should incorporate a self-resetable thermal cut-off which will disconnect at 110ºC. The heating element should be Automatic disconnected ½ second before motor stop. The heating element should incorporate an automatic regulation of air temperature on ambient temperature system. The hand dryer should have an aluminium asymmetrical double inlet fan wheel, and the fan scroll shall be made of a fire resistant plastic 94-V0. Dryer shall deliver 450 m3/h of air at 49 ºC and 95 Km/h velocity during user controlled drying cycle. The dryer shall have a total power of 2.350 Watts with a consumption of 10.9 A. Noise level should be 65 dB at 2 m distances. Protection level against water splashes should be rating Ipx1. Overall dimensions shall be 267×237×150 mm. Unit shall VDE approved and CE marked and comply with electrical safety directives 73/23/CEE& 93/68/CEE and electro-magnetic compatibility directives 89/336/CEE & 92/31/CEE. In recessed version should comply with ADA projection requirements.Surface mounted hand dryer shall be model M02A sensor operated, stainless steel bright finish, manufactured by Aubo ,China. * Installation * Serial Installation Nº dryers to be fitted:In toilet areas with a normal frequency of use and only one wash-basin: 1 dryer.In toilet areas with a normal frequency of use and more than one wash-basin: 1 dryer for each 2 wash-basins.1 row of 4 wash basins: 2 dryers; 1 row of 6 wash basins: 3 dryers; 1 row of 8 wash basins: 4 dryers.In toilet areas with high traffic and more than one wash-basin: 2 dryers for each 3 wash-basins.1 row of 4 wash basins: 3 dryers; 1 row of 6 wash basins: 4 dryers; 1 row of 8 wash basins: 5 dryers.Ideal Location:Between the wash-basin and exit. It is not recommended to install dryer between wash-basins, next to urinals, lavatories and showers. If installing automatic dryers over marble surface or ledge, the minimum distance from the dryer to the ledge must be 400 mm. It is recommended that hand dryers be distributed throughout the washroom area to avoid overcrowding.Recommended heightsDistance from the floor
|
Hilfe
Zu Favoriten 
Dem Warenkorb hinzugefügte Favoriten
